Vehicles
29 not categorized PORSCHE 997 REAR BEARINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.150TBF900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the rear of the control arm is part # 150tbr900 sold individually. 2 necessary per car.
$48.40
Make a selection 150PB100919 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 91491218KIT Our 17-piece clutch package contains everything we use in our shop minus the flywheel for a perfect clutch replacement. beware of lesser kits, you will need all of these parts! Included is the clutch installation manual. General Fitment914 1970-76
$632.40
Make a selection 91530239906 Rear pinion shaft bearing. 356from 1957-64 (644,716,741 trans.) View/Change Diagram
From $271.23
Make a selection 95111691100 Does your 924 tach needle climb in high gears and not move the car like it should? Does your 924 make a grinding noise in neutral? Does your 944 seem to lurch during acceleration after shifts? These are all typical clutch problems. We offer complete packages to help you do it right! All clutch packages include clutch disc pressure plate release bearing and the always forgotten needle bearing (the little bearing in the flywheel that ruins your drive tube when it goes bad), the pilot bearing and the rear main seal. View/Change Diagram
From $264.50
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 91411600002 Our 18-piece clutch package contains everything we use in our shop for a perfect clutch replacement. beware of lesser kits, you will need all of these parts! Included is the clutch installation manual. Kit includes: rear main seal, throwout bearing, 2 throwout bearing clips, flywheel, front trans. Seal, 2 cv joint gaskets, flywheel o-ring, ball stud cup, 2 muffler gaskets, needle bearing, cv joint bolt, clutch alignment tool, flywheel crush washer, felt washer, pressure plate, clutch disc, clutch installation manual. General Fitment914 1970-76
$917.39
Make a selection 99905304104 High quality, European made, sealed angular contact bearing. This number is superseded from 999 053 041 01, 999 053 041 02 and 999 053 041 03. Sold individually. Left or right side fitment. Please note: this is the front bearing for the 964 / 965 / 993 and 996 models. It is the front and rear bearing for the 986 models. View/Change Diagram
From $42.00
Make a selection ER2071600 Elephant racing low-friction control arm mounts allow for free control arm movement, eliminating any potential for binding. Elephant racing corrected a key factory design limitation:our mounts self-align in all axis, becoming collinear to avoid binding as the arm moves through its range of motion. The low-friction control arm mounts self-align in both the horizontal and vertical planes. The result is collinear front and rear mounts delivering smooth non-binding action. You get superior performance and a smoother ride. Kit includes everything required to upgrade one car. Factory rear mounts are replaced with our self-aligning mounts. Factory front mounts are retained and augmented with self-aligning washers. ...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76 912 1965-69
$225.00
Make a selection 99905302001 Wheel bearing. View/Change Diagram
From $49.27
Make a selection 99911303850 Rear wheel bearing seal. Sold each, 2 needed per car. View/Change Diagram
From $16.50
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$482.89
Make a selection 99905906400 This is the rear differential tapered roller bearing that sits between the differential and the flange (closest to the flange). We recommend replacing this bearing with any differential rebuild. Sold individually. View/Change Diagram
From $48.50
Make a selection FVD3439642PSS9 The FVD camber plate kit replaces the front and rear original rubber top strut mount bushings. We manufacture each camber plate and mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with spherical bearings which allows a wide range of camber possibilities. This kit contains: 2 front camber plates 2 rear camber plates please note: this kit only works in conjunction with a pss9 / pss10 coil over (double spring) suspension in front and rear. General Fitment911 1989-94
From $1,204.50
Make a selection FVD33310005 The FVD rear shock mount replaces the original rubber top strut mount bushings. We manufacture each mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with a spherical bearing which improves the shock and springs performance. Sold individually. Please note: this shock mount only works in conjunction with a coil over (double spring) suspension. General Fitment911 1994-98
From $341.00
Make a selection FVD3439641PSS9 The FVD camber plate kit replaces the front and rear original rubber top strut mount bushings. We manufacture each camber plate and mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with spherical bearings which allows a wide range of camber possibilities. This kit contains: 2 front camber plates 2 rear camber plates please note: this kit only works in conjunction with a pss9 / pss10 coil over (double spring) suspension in front and rear. General Fitment911 1989-94
From $1,245.20
Make a selection MIS2000E Great inexpensive way to convert your four lug wheel bolt pattern to the five lug 911 style so you can add six inch five lug wheels. kit consists of General Fitment914 1970-76
$1,163.46
Make a selection P911830 This is a true, 935-style spring plate design for the c2/4. Under hard cornering, rubber mounted suspension points can deform effecting critical angles of camber and toe. Erp/weltmeisters spring plates incorporated heim-joint linkage for precise suspension movement, a necessity for high speed handling and stability. The plates have also been designed to be mounted either right-side up or upside-down, offering a larger number of alignment settings. General Fitment911 1989-94
$795.99
Make a selection 1306107997 Our billet aluminum strut mounts are a must when upgrading to a race suspension such as moton or bilstein pss9/10. The OEM units flex and move during cornering which causes spongy handling characteristics. Our engineered mounts will add more precise handling and road feel. Each of our components are cnc machined from 6061-t6 aluminum, assembled with stainless steel spherical bearings and hard anodized. General FitmentBOXSTER 1997-04BOXSTER 2005-08 CAYMAN 2006-08
$827.63
Make a selection S701041 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Note: two required per car. General Fitment911 1998-05911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11 CAYMAN 2006-08 BOXSTER 2005-08
$306.90
Make a selection S721041 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Sold each, two needed per car. General Fitment911 1994-98
$306.90
Make a selection 113501277A • 924 1976-85 rear outer View/Change Diagram
From $35.00
Make a selection 150TBR900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the front of the control arm is part # 150tbf900 sold individually. 2 necessary per car.
$49.50
Make a selection
$22.62
Make a selection AK37354 Bilsteins are original equipment on many Porsches and have won, for Porsche, countless races. Bilsteins are the highest quality shocks made and will last the lifetime of your Porsche. Bilstein racing shocks and struts are specifically set to meet the rigourous demands of driving competition. Their success should be measured by the unprecedented levels of acceptance and use by professional drivers in virtually all major motorsports. Rallye and race units may include such features as spherical bearings, adjustable spring-seats longer or shorter than standard dimensions. General Fitment944 1989-91944 1985-88
$571.64
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |